Cleaning & Maintenance

New! OptiMate 1 Duo features precise microprocessor controlled charging and long term maintenance. Maintain any type of 12 volt lead-acid battery, filler cap / wet cell, sealed AGM (MF) or GEL and 12.8/13.2V lithium (LiFePO4) batteries without overcharging. Ideal for vehicles that are seldom or seasonally used, or in storage. The OptiMate maintenance program delivers only what the battery needs, never overcharges, never undercharges.

• Ideal for Standard, AGM & gel 12V batteries from 2 – 30Ah & Lithium (LiFePO4) 12.8/13.2V batteries
• Cost-effective 12V battery maintenance
• 0.6A (constant current) charging amps
• Indoor use (lowest temperature: -4°F / -20°C)
• Low Volt Start of 4V
• Global input (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
• Dust proof plug-in case, with 12ft / 370cm charge lead ending in SAE connector
• No risk of overcharging, totally safe for vehicle electronics
• Sparks suppressed, Safe for long-term battery maintenance, Automatic shut-down if short-circuited or battery disconnected
• Weatherproof battery lead & battery clip set included

Smart in-line 3300mA USB charger kit, with standby mode and vehicle battery monitor.

The sealed in-line battery to USB 3300mA charger with 200cm / 80″ of cable and O-31 battery lead, delivers safe and fast USB charging of any device mounted outside on the handlebar or inside your tank or pannier – Cable routes to where USB charging is needed!

Supply cable (100cm / 40″) with M6 / 1/4″ rings fit all powersport battery terminals. – Fuse protected.

Charges 1x USB device with up to 3300mA current available (or get optional O-110 USB splitter and charge 2 devices). – Charge current adapts to connected device for safe recharging.

Weatherproof USB charge port easily zip-tie to handlebar, strut or even brake / clutch cable – Seals againt inserted USB cable for charging in any weather!

Built in protection turns off USB charging & prevents your parked vehicle’s LFP (LiFePO4) or AGM (Pb)battery from draining – Starts back up when vehicle engine fires up.

Monitors and displays parked vehicle’s battery status – Indicates battery is ‘start ready’ at the blink of an LED!

Smart 2400mA USB charger, with standby mode & vehicle battery monitor.

The portable & compact SAE to USB 2400mA charger for safe and fast charging of any USB device, including your phone, camera or GPS.

Connects to battery lead with industry standard SAE 2-pin connector – Seals perfectly when mated with OptiMate SAE!

Charges 1x USB device with up to 2400mA current available (or get optional O-110 USB splitter and charge 2 devices). – Charge current adapts to connected device for safe recharging.

Creates weatherproof seal against inserted USB cable, or ‘rideproof’ cap seals when not in use – Worry free phone, camera or GPS charging in any weather!

Built-in protection turns off USB charging & prevents your parked vehicle’s LFP (LiFePO4) or AGM (Pb)battery from draining – Starts back up when vehicle engine fires up.

Monitors and displays parked vehicle’s battery status – indicates battery is ‘start ready’ at the blink of an LED!

Technosynthese® 4-Stroke lubricant – Ester technology - Improved shear resistance. Smooth shifting. Meets JASO MA2 specifications for optimal wet clutch performance. Suitable for catalytic converters.

Types of Use

Street & road bikes, trails, off road bikes, enduro, trial…fitted with 4 Stroke engines, integrated gearbox or not, wet or dry clutch, engines meeting Euro 2, 3, 4 or 5 emission regulation, fitted with exhaust gas after treatment systems: catalytic converters, air injection into exhaust pipe... Suitable for specific SUZUKI, YAMAHA, KAWASAKI engines requiring SAE 10W-40 viscosity grade oil. Other uses: street bikes without catalytic converters, scooters, ATV’s, UTV’s…

Protection

Synthetic lubricant Technosynthese® reinforced by Ester base stock to warranty anti-wear properties and improve gear protection and lifetime. Improved oil film resistance at high temperatures for engine durability. Optimized Phosphorus and Sulfur content (JASO MA2 < 1200 ppm) for better operating conditions of catalytic converters. The innovative anti wear additives package provides excellent gearbox protection. FZG Gear Test results: Pass FLS 14. The FZG (Forschungsstelle für Zahnrader und Getriebebau) Test, evaluates fluid lubricating and wear protection properties at the interface of a loaded set of gears.

Comfort

JASO has created its own 4-stroke motorcycle standard -JASO T903- which has three grades MA, MA1 and MA2. JASO MA2 offers the most efficient friction levels to guarantee the clutch engagement during the three riding modes: Starting, Acceleration and Constant Speed.

100% Synthetic Ester based motorcycle lubricant for high performance bikes, sports bikes, street & road bikes, trails, off road bikes, enduro, trial fitted with 4-stroke engines, integrated or non-integrated gearbox, wet or dry clutch, engines meeting Euro 2 or Euro 3 emission regulation, fitted with exhaust gas after treatment systems: catalytic converters, air injection into exhaust pipe. 

Types of Use

High performance bikes, sports bikes, street & road bikes, trails, off road bikes, enduro, trial…fitted with 4 stroke engines, integrated gearbox or not, wet or dry clutch, engines meeting Euro 2, 3, 4 or 5 emission regulation, fitted with exhaust gas after treatment systems : catalytic converters, air injection into exhaust pipe...

Other uses: street bikes without catalytic converters, scooters, ATV’s, UTV’s…

HD 80W-90 is an Extreme Pressure gearbox and differental lubricant.

Motul HD 80W90 Transmission Oil

Motul's most robust gearbox oil is the HD 80W90 Transmission Oil. Prepared for abuse, Motul HD Transmission Oil is suitable for all mechanical transmissions: synchronized or non-synchronized gearboxes, shared gearbox / differential combinations, transfer boxes and hypoid differentials without limited slip systems. Motul HD is anti-foam, anti-corrosion and stays in 90 grade after KRL 20 hours shear test as requested by SAE J306 Standard.

Features: 

• Fully conventional formulation
• Designed especially for high load applications
• Extreme anti-wear properties
• Stays in 90 grade after KRL 20 hours shear test as requested by SAE J306 Standard
• Suitable for all transmissions without limited slip systems
• Safe for synchronized or non-synchronized gearboxes, shared gearbox / differential combinations, transfer boxes or hypoid differentials
• Recommended for heavy loads and low revolution speed or moderate loads and high revolution speed
• See spec sheet for full details
• Meets or exceeds API GL-4, API GL-5

Hiflofiltro Premium Filters: Superior Quality Motorcycle Filters

Hiflofiltro - the world’s first TÜV approved oil filter. Engineered to extreme quality standards, Hiflofiltro is the complete range of oil and air filters for motorcycles, scooters, ATVs, and watercraft, providing the ultimate level of protection for your engine.

The Hiflofiltro oil filter features high performance tri-fibre filtration media for optimum filtration, high capacity, and improved oil flow. The HF204RC includes a nut, making oil filter changes a breeze. No more messing about with oil filter wrenches.

Will this work for my bike?
This filter can be used for a number of makes and models, including most Triumphs. See the complete list of applications here: http://www.hiflofiltro.com/catalogue/filter/hf204rc

Hiflofiltro Premium Filters: Superior Quality Motorcycle Filters

Hiflofiltro - the world’s first TÜV approved oil filter. Engineered to extreme quality standards, Hiflofiltro is the complete range of oil and air filters for motorcycles, scooters, ATVs, and watercraft, providing the ultimate level of protection for your engine.

The Hiflofiltro oil filter features high performance tri-fibre filtration media for optimum filtration, high capacity, and improved oil flow. The HF153RC includes a nut, making oil filter changes a breeze. No more messing about with oil filter wrenches.

Will this work for my bike?
This filter can be used for a number of makes and models. See the complete list of applications here: http://www.hiflofiltro.com/catalogue/filter/HF153RC

FEATURES

• Long Life 100% synthetic fluid
• Applications: All types of hydraulic actuated-brake and clutch systems in accordance with DOT 5.1, DOT 4 and DOT 3 manufacturers' recommendations.
• Fluidity specially designed for anti-locking brake system (ABS)

SPECIFICATIONS

• Dry Boiling Point: 270°C (518°F)
• Wet Boiling Point: 185°C (365°F)
• Standards: FMVSS 116 DOT 5.1 non silicone base & DOT 4 & DOT 3 / SAE J 1703

ACF-50 Anti-Corrosion Fogging Oil

ACF-50, Anti-Corrosion Formula, is a state of the art, anti-corrosion lubricant compound, specifically designed for the Aerospace Industry. It is an ultra Thin Fluid Compound (TFFC) that actively treats metal using advanced polar bonding technology.

ACF-50 actively penetrates and "creeps" into the tightest seams, lap joints, micro-cracks, and around rivet heads, displacing moisture and other corrosive fluids (orange juice, coke, coffee, salt water) in these corrosive prone areas.

ACF-50's thin film acts like an "OFF SWITCH" for corrosion remaining effective for up to 24 months.

Kills and stops corrosion on contact.

Protects, Penetrates, Lubricates.

Features:

• Approved for use on all metals & electronics
• Can be sprayed on, wiped on, or fogged for complete protection.
• The clear ultra-thin fluid film leaves a non-greasy atmospheric barrier to protect the base metal.
• Spray directly into electrical connections and components to prevent corrosion induced failures.
• Chemically neutralizes the corrosive effects of road salt.
• Will not dry out or trap moisture in
• Excellent vehicle storage preparation and protection

How to Use:

• ACF-50 is 95% product, hence virtually no propellant. Keep the tin in a warm environment, shake very well before use and remember a little ACF-50 goes a long way, so keep a rag handy to soak up any excess - then use the rag to help spread the product.
• ACF-50 has strong capillary action so will creep into all the areas that moisture can, 'actively' pushing out moisture and replacing it with protection. Go cautiously when applying to the calipers to ENSURE YOU KEEP IT OFF THE BRAKES. Use ACF-50 anywhere, except the brakes, on your bike including the engine and exhaust (will smoke on the first start and burn off down pipes but still slows down corrosion process). Safe on paintwork, most rubbers and brings up black plastic trim a treat.
• ACF-50 contains no water and is approved for electrics so spray directly into electrical joints and components where it will prevent corrosion-induced failures and high resistance joints. Works well at stopping dirt, mud, and salt from sticking. You can come back from a winter ride with the bike 'white with salt' - a quick wash off and it's gone with the bike still protected. Areas not in direct contact with the elements i.e. tank, seat areas, electrics require treating approx. once a year. Other exposed areas re-apply as necessary. You can tell the product is still 'Active; as water will bead on contact...having no water content and not being water-soluble ACF-50 only dissipates by being 'sacrificial' whilst stopping existing or new corrosion so just re-treat as required.

Colorless and sticky lubricant specifically designed to lubricate all chains of road bikes and karts.

Types of Use

All types of chains: standard and with O-RING, X-RING, Z-RING. Street motorcycles, go-karts. Specially recommended for very fast motorcycles, MOTUL CHAIN LUBE ROAD adheres to the chain even at high speeds.

Package size: 400ML (9.3OZ)

Colorless and sticky lubricant specifically designed to lubricate all Off-road chains.

Types of Use

All types of chains : standard and with O-RING, X-RING, Z-RING.
Cross, enduro, trial, trail motorcycles or quads, ATVs.
Specially recommended for off road use: MOTUL CHAIN LUBE OFF ROAD repels sand and soil.

Package size: 400ML (9.3OZ)

Motul Chain Care Kit

Complete chain care for wherever the road takes you

Includes: 

• 9.8 oz of Motul C1 chain cleaner aerosol: degreases chains and removes encrusted deposits of grease, sand and dirt without using chlorine
• 9.3 oz of Motul C2 chain lube "on road" formula: colourless and sticky lubricant designed for road bikes; compatible with O-ring, X-ring, and Z-ring chains; water- and salt-resistant; very strong tack to adhere to chain even at high speeds; protects against corrosion and extends chain lifespan.
• Motul double-sided chain brush
• 1 pair black nitrile gloves
• Motul 4.1" X 1.1" sticker

• Double-ended brush for cleaning chains and other components
• Three-sided brush to clean chain rollers and side plates in one operation
• Long, straight bristles on opposite end to clean hard to reach areas
• Durable nylon brush and high quality plastic handle

IPONE VISOR RAIN OFF is a visor cleaner with a water-repellent effect. It places a protective film on the visor allowing water to slide off easily.

Spray the product on the visor, let it dry for 2 minutes and wipe with a soft cloth.

• Repels water from helmet visor
• Improves visibility by shedding water
• Suitable for glossy and matte helmets
• No marks

MOLECULE ANTI-FOG improves visibility and is designed specifically to inhibit fog causing moisture on the interior of shields. Apply to the inside surface of visors, goggles or wind screens to guard against distortion.

• Reduces fogging & improves visibility
• Cleans surface of dirt & chemicals
• Recommended for helmet visors, goggles and wind screens

Caution: Not for use with Stilo visor.

Cleaning and nourishing cream formulated with olive oil soap, glycerine and turpentine oil. Cleanses, nourishes and revives all types of leather on motorcycles or motorcycle gear from jackets, to boots, and gloves.

Like water off a duck's back. This product extends the life of your leather and wax items. The ultimate in long lasting protection. Won't stain stitching. Sweet smelling and insect repelling. Leather Food. Moisturise-soften-preserve. Helps to waterproof your leather. Reduces water absorption. Conditions and revives the look of the leather or wax fabric. Works on wax cotton (Barbour type) jackets too! 

Suitable for use of motorcycle clothing, equestrian equipent and footwear. 

Product info:

• 1 x 150 mL tin of Goldtop Ducks Wax Water Repellent Balm
• Effects on tan coloured gloves as shown here on Youtube

Like water off a duck's back. This product extends the life of your leather and wax items. The ultimate in long lasting protection. Won't stain stitching. Sweet smelling and insect repelling. Leather Food. Moisturise-soften-preserve. Helps to waterproof your leather. Reduces water absorption. Conditions and revives the look of the leather or wax fabric. Works on wax cotton (Barbour type) jackets too! 

Suitable for use of motorcycle clothing, equestrian equipent and footwear. 

Product info:

• 1 x 30 mL tin of Goldtop Ducks Wax Water Repellent Balm
• Effects on tan coloured gloves as shown here on Youtube

NOTE: Due to manufacturer restrictions, this item cannot be shipped to addresses outside of Canada.

The maintenance of textile garments requires special attention, especially when they contain waterproof and breathable membranes. REVIT! TEXTILE WASH detergent maintains the specific qualities of breathable waterproof clothing, when washing by machine or hand.

Always follow the wash and care instructions on garment labels.

NOTE: A $75 handling fee is applied to shipping cost due to this item being oversize/overweight.

The Spooled Rear Stand lifts spool-equipped bikes. It is width adjustable to fit virtually all spool-equipped sportbikes. The Pit Bull rear motorcycle stand was designed as a modular platform which allows SS, Standard, 999, and GP top supports to be used interchangeably. Sold complete with top supports. Spools sold separately.  

NOTE: Use a Fully Adjustable Spooled Rear for a 2nd gen Busa as well as Ninja 1000 or ZX14R models with stock fender as that stand will clear the low hanging rear fender on these bikes. If you have a fender eliminator installed on those bikes, you may use this motorcycle stand on any of those bikes.

As of November 2022, all of our rear stands come standard with the 16" removable handle.  

If you're not sure which stand is right for your bike, check out our bike specific navigation, view all motorcycle stands or simply contact us and ask!  Pit Bull stands are known for our distinctive gold and red finish and are not available in other colors.

FITTING NOTES:

Handle Length: Fixed handle: 12", Removable handle: 16"
Width Adjustability: 10.5"-14.75", (Narrow/Vintage Version: 8"-11.25")
Height from ground, supports: 13-1/8"

NOTE: Stand will not work on '15+ Versys 650 or Vulcan S models with stock fender. Use the F0043-000, Forward Handle Spooled Rear in this case.

Instructions can be found here.

NOTE: A $75 handling fee is applied to shipping cost due to this item being oversize/overweight.

The Spooled Forward Handle Rear lifts spool-equipped bikes. It is width adjustable to fit virtually all sport bikes. It is also height adjustable to set clearance under rear wheel. Same as Standard Forward Handle Rear except for interchangeable top supports. Sold complete with top supports.

Advantages to the forward handle stands: a)user can hold bike's handgrip when getting stand into place, b)no part of stand is behind bike, and c) lower bar of stand helps align axle when installing rear wheel.

NOTE: Not recommended for Moto Guzzi, Buell XB Series, Vintage or 125GP machines.

NOTE ABOUT REMOVABLE HANDLE:  As of Winter 2022, this stand only comes with a removable handle. This is primarily beneficial for storage and/or shipping.  This handle is not removable while the stand is in use but has become a favorite among customers who need this stand to store flat when not in use.  This is also a very handy option for international shipping as it will be able to go in a flat box.

FITTING NOTES

Width Adjustability: 9-7/8" - 15-1/2"

Height from Ground: 12-3/4" - 15-1/2"

For instructions for use, click here.

Counteract CBB-EP8 Tire/Tube Mounting Compound 8lb Bucket

• Designed to assist in mounting rubber tires and tubes on all types and sizes of wheels
• Fortified with rust inhibitors to provide protection against corrosion of aluminum or alloy wheels
• Fully compatible with Counteract balancing beads
• Fast-drying formula will not freeze
• Performs well on low profile tires or tires with stiff beads
• Environmentally friendly and petroleum-free
• Reduces wear and tear on tire changing equipment
• Available in 8lb bucket

• Easily apply your tire mounting lubricant with control.
• Perfect for euro paste mounting formulas.
• Works best with Counteract Euro Paste tire and tube mounting compound.
• Premium quality brush with soft and flexible head.
• Angled head allows for easier application.

Tool-Check PLUS, 39 pieces

• Zyklop mini 1/4" ratchet features a robust, drop-forged steel design and a return angle of 6° for work in close quarters
• Kraftform handle geometry has perfectly shaped contact areas for the fingers
• Rapidaptor bit holder with free-turning sleeve can be used as an extension and for rapid bit changes without any special tools
• Tough bits and sockets are ideal for both manual and power tool applications
• "Take it easy" tool finder with colour coding according to size makes finding the right tool simple

Set Includes:

• Zyklop mini 1/4" ratchet
• Kraftform handle
• Rapidaptor bit holder
• Metric sockets (5.5, 6, 7, 8, 10, 12, 13 mm)
• POZIdriv bits (PZ 1, 2, 3)
• Torx tamper proof bits (T10, T15, T20, T20, T25, T30)
• Slotted bit (1 mm)
• Hex-square adapter
• Phillips bits (#1, #2, #3)
• Torx bits (T10, T15, T20, T25, T30, T40)
• Hex bits (3, 4, 5, 6, 8 mm)

• Flexible shaft allows easy access to awkward locations during removal and installation of hose clamps
• Comfortable grip, high-torque handle
• Hollow drive handle stores sockets and bits
• Contains: 4, 6, & 8mm sockets, 4mm flat head bit and Phillips #2 bit
• Length: 300mm

Features:

• Tempered C hook wrenches are specially designed for use with slotted retaining rings
• 4 mm thin hook allows to access confined areas in motorcycle steering and suspension
• Made of hardened chrome vanadium steel

Dimensions:

• Size: 51-120mm (2" - 4 3/4") dia.
• Overall length: 285 mm (11-1/4")

Features:

• Tempered C hook wrenches are specially designed for use with slotted retaining rings
• 4 mm thin hook allows to access confined areas in motorcycle steering and suspension
• Made of hardened chrome vanadium steel

Dimensions:

• 32 - 76 mm: Overall length: 215 mm (8-7/16")